Home / Hydraulic Breakers / Side Type
NEWLAND · Side Type
NLB85 Side Type Hydraulic Breaker
NEWLAND Side Type hydraulic breaker — representative image
For NLB85 Side Type, the NLB series gives screening references of 7–14 Ton excavators, 60–100 L/min required flow and an 85 mm tool. Compare NLB75 and NLB100 within their different overlaps, then confirm the side mounting interface, complete assembly mass and specified hydraulic package.
Housing: Side Type
Carrier range: 7-14 Ton
Required oil flow: 60-100 L/min
Tool diameter: 85 mm
Excavator ranges and hydraulic specifications are NLB series reference values. Confirm the complete Side Type assembly and attachment mass for your carrier.
This page shows one model from our range. Contact NEWLAND for other models, excavator weight ranges and tool diameters.
Choose your NLB85 housing type
Compare the three housing layouts for the same NLB model. The photos illustrate the housing layouts. Use the drawing for the selected model to check dimensions and mounting fit.
Box Type
Top Type
Side Type
Currently viewing NLB85 Side Type
NLB85 model reference specifications
These figures are NLB series reference values for initial model comparison. Request the total operating weight for the quoted Side Type assembly, including the mounting components and tool.
| Specification | Series specifications / configuration notes |
|---|---|
| Suitable excavator range | 7-14 Ton |
| Complete assembly operating weight | Confirm the Side Type assembly weight |
| Required oil flow | 60-100 L/min |
| Setting pressure | 190 bar |
| Operating pressure | 130-160 bar |
| Impact energy | 1355 J |
| Impact rate | 400-800 blows/min |
| Hose diameter | 3/4 inch |
| Tool diameter | 85 mm |
Carrier weights use the catalog unit “Ton.” Confirm the unit basis when comparing them with your excavator specifications. Setting pressure and operating pressure are separate fields. Use the specification and mounting drawing for the quoted assembly to check the final installation.
Distinguish the two overlaps around NLB85
NLB85 shares 7–9 Ton with NLB75 and 10–14 Ton with NLB100 in the series carrier ranges. These are different comparison areas. NLB85 lists 60–100 L/min required flow and 130–160 bar operating pressure, while NLB100 lists 80–110 L/min and 150–170 bar.
At the lower overlap, NLB75 lists 50–90 L/min and 120–150 bar. Check the actual attachment supply against the model being considered. A carrier within the broad NLB85 range still needs its hydraulic circuit and complete Side Type installation assessed.
Bring the side mounting dimensions into the selection
Identify the carrier, existing coupler and any adapter that will remain between the stick and breaker. Supply the interface drawing with pin diameters, pin-center distance and mounting width. Label where measurements were taken so the proposed bracket can be reviewed against one consistent dimensional reference.
The weight of the Side Type assembly needs its own package definition. Request the mass and included bracket, tool and connection components, then compare the complete arrangement with the carrier’s permitted limits. No Side Type assembly weight is established by the generic NLB series sheet.
Confirm the hose and 85 mm tool interfaces
The series lists a 3/4 Inch hose diameter for NLB85, compared with 1/2 Inch on NLB75. This nominal diameter does not identify the hose-end fittings or approve an existing return line. Confirm the actual connections and routing with the intended carrier installation.
Use the 85 mm tool diameter with the correct upper profile, retaining features, length and requested tip. Record whether the package includes spare working tools or adapters. Keeping those references with the quoted Side Type build supports clear receiving checks and later parts identification.
Compare NLB85 Side Type with nearby models
Compare the model references below alongside the actual Side Type attachment mass, mounting interface and documented carrier circuit.
| Model / housing | Excavator range (Ton) | Required oil flow (L/min) | Operating pressure (bar) | Tool diameter (mm) |
|---|---|---|---|---|
| NLB85 Side Type (this product) | 7-14 | 60-100 | 130-160 | 85 |
| NLB75 Side Type | 6-9 | 50-90 | 120-150 | 75 |
| NLB100 Side Type | 10-15 | 80-110 | 150-170 | 100 |
NLB85 Side Type questions
Is the 3/4 Inch hose entry enough to connect NLB85 Side Type?
It is a series diameter reference. Hose ends, routing, carrier circuit and the approved return arrangement still need to be confirmed for the specific mounting and connection package.
Pricing and availability for NLB85 Side Type
Send the carrier details, documented flow and pressure, mounting or quick coupler measurements, requested Side Type package, quantity and delivery country. Ask for the total weight and included components to be listed in your quote.
The email includes NLB85 and Side Type in your inquiry.
Send your inquiry
Include the product or part, quantity and delivery country. For replacement parts, add the breaker model, part number or key dimensions if available.
Have photos or drawings? Email them to gordon@newlandbreaker.com. Please also read our privacy notice.